[Resolved] Schematic for Solidremote 202U

Home Forums Wireless Kits Support (KIT-1, KIT-2, TX134 etc) Schematic for Solidremote 202U

This topic contains 7 replies, has 3 voices, and was last updated by   William 3 months ago.

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • #11112 Reply

    mfoster
    Participant

    I just purchased 5 Solidremote 202Us on Amazon and I need to modify them so that both relays are controlled by the same remote button. The relays will be configured in the pulse mode and the load will be connected to the normally closed contacts so that an always-on system can be power cycled.
    Murray

    #11127 Reply

    William
    Keymaster

    Hello Murray,

    Do you mean you want to treat both onboard relays as single relay? if so why not connect all wires to one relay? due to current limits?

    Please let me know, thanks.

    Kind Regards,
    William

    Buy KIT-1 at Amazon.com here
    Want better range and security? check out KIT-2
    Need spare remotes for KIT-1 or KIT-2? see here

    #11141 Reply

    mfoster
    Participant

    Yes, I want to treat both onboard relays as a single relay. Two different voltages are being switched. I’ve previously modified remote control switches like these and I probably can suss out the traces to cut and bridge but a schematic will make it easier. No problem if you need to have an NDA to release the schematic.

    #11148 Reply

    William
    Keymaster

    Sure, I asked our engineer, and here you are the photo connection guide.

    https://postimg.org/image/8a2a6lrjx/

    Please let me know if it works, thanks.

    Buy KIT-1 at Amazon.com here
    Want better range and security? check out KIT-2
    Need spare remotes for KIT-1 or KIT-2? see here

    #11246 Reply

    mfoster
    Participant

    Hi William,

    This worked great. However, I realized after I read the programming instructions more carefully that I could just program both relays to respond to the same button press, dah. 8^)

    BTW, do you sell a compatible single button controller?

    #11258 Reply

    William
    Keymaster

    Hello,

    I’m afraid the modification you did is the only way to make one button control two relays, since the receiver will only activate one relay at a time.

    Sorry we don’t have single button remote, we only have 4 and 2 buttons version, and only 4 button version is available on Amazon.

    Buy KIT-1 at Amazon.com here
    Want better range and security? check out KIT-2
    Need spare remotes for KIT-1 or KIT-2? see here

    #12945 Reply

    Mike Fisher

    I need to activate both relays with one button action, because one relay is merely pulling a logic input to ground, the other relay needs to switch 12 vdc to an LED. Can I modify the 202U to drive both relays from the same current driver?? A simple picture / schematic of the board layout regarding the relays would be so helpful.

    Kind Regards,

    Mike Fisher
    fisherm054@gmail.com

    #12946 Reply

    William
    Keymaster

    The post is more than one year ago, and information on it is outdated.
    In our V5 version, you can use one button to control both relays, just program both relays to the button you need.
    No mod is required anymore.

    Buy KIT-1 at Amazon.com here
    Want better range and security? check out KIT-2
    Need spare remotes for KIT-1 or KIT-2? see here

Viewing 8 posts - 1 through 8 (of 8 total)
Reply To: Schematic for Solidremote 202U

You can use BBCodes to format your content.
Your account can't use Advanced BBCodes, they will be stripped before saving.

Your information: